Printing Profile

Printing Profile

Simplify 3D Slicer version: 4.1.2 Our print profile is modified based on the one created by Chris Elkins. If you are using other slicer may also use this as a reference to tweak on your setting. Ender 3 / Ender 3 Pro / Ender 4 (uploaded at 2020-07-07) CR10 and CR10S...
Extruder Motor Skipping

Extruder Motor Skipping

Extruder skipping most probably causing by: 1) Printing speed too fast, nozzle not hot enough Try slow down printing speed and increase temperature on nozzle. 2) Skip during printing the first layer It could be the bed leveling issue, the nozzle is too close to the...
IdeaMaker

IdeaMaker

Just come across this slicer Ideamaker by Raise3D. Haven’t really use it to print anything yet. By having a quick glance, the interface looks slightly similar to Simplify 3D. https://www.raise3d.com/ideamaker/ We use Simplify 3D instead of cura, because we like...
Model not printed properly

Model not printed properly

A customer bought our filament and asking how come the print turn out so bad. He was using the same print setting for their previous PLA wihtout any issue. Kindly take note that filament made by different manufacturer may have different characteristic, they may need...
Printing Colour Inconsistent

Printing Colour Inconsistent

To be honest we have no clue on this issue. Base on experience this could be causing by the printing speed and the temperature changing during printing. We also found out there are some user out there using different brand of PLA, 3D printers and slicer also having...
Z Banding/Ribbing

Z Banding/Ribbing

Z banding / ribbing may caused by: 1) 2 bolts on the lead screw nut too tight Loosen slightly of the 2 bolts on the lead screw nut, so that it can have slight allowance for the lead screws to move and compensate the banding. 2) Spring couplet doesn’t provide...
Layer Shift

Layer Shift

Belt tension will loose over time X Axis Layer shift 1) Check the 2 bolts which attach the hotend to the carriage. Thighten them if they are loose. 2) Check X belt tension, thighten the belt Will help. Y Axis Layer shift 1) Check Y belt tension, thighten the belt Will...
Surface Artifact / Rough

Surface Artifact / Rough

Over Extrusion Ringing / Ghosting Z banding Layer shifting Salmon skin Surface artifact can possibility caused by: 1) Over extrusion Check out over extrusion issue. 2) Ghosting / ringing effect Printing speed too high can cause the ringing effect on the surface. Check...
Bad First Layer / Warping

Bad First Layer / Warping

Bad first layer and warping issue is the most common issue experienced by many beginners. It can caused by: 1) Bed not leveled If the first layer not printed consistent, some area thicker or some area thinner. Check bed leveling, make sure the bed is leveled properly....
Bed Leveling Problem

Bed Leveling Problem

Bed leveling issue can be caused by: 1) Build platform wobbly Check wheels under the build platform, if any of them can be spin freely, adjust the eccentric nut, just thight enough to eliminate the wobbly bed. Push the bed, if you feel it is bumpy when moving, this is...
Overhang Surface Very Rough

Overhang Surface Very Rough

This can be caused by part cooling problem. If you notice the overhang area of your part is very rough, the support are stuck too firm on the actual part and hard to be removed, this could be: 1) Part fan not strong enough, or only at one side Upgrade to a 5015 radial...
Over Extrusion

Over Extrusion

Over extrusion can caused by: 1) Nozzle worn out Often replace the normal brass nozzle if you print a lot. We will suggest to change the nozzle and PTFE tube together, since you may need to clean the internal of the heat sink and the aluminium heated block. It could...
Popping Sound When Printing

Popping Sound When Printing

Popping sound and bubbles in extruded filament most probably is due to the filament is moist. 1) Preventing moist filament Remove unused filament from the 3D printer, keep it in a ziplock bag with some silica gel bags. This will able to prevent the filament being...
PTFE Tube Keep Coming Out

PTFE Tube Keep Coming Out

The PTFE/teflon tube keep coming out from the pneumatic connector. 1) Printing speed to high, nozzle temperature not high enough If you are using our filament, kindly use 200°c or 210°c for the nozzle and 50 mm/s for the general printing speed. It should help to solve...
Under Extrusion

Under Extrusion

Under extrusion may caused by: 1) PTFE tube worn out Replace PTFE tube will solve the problem, we suggest to replace both PTFE tube and nozzle together. As you may need to clean the internal of the heatsink and the heating block. You can purchase the related parts at...
5 Channel Power Amplifier

5 Channel Power Amplifier

We have introduced a DAC done by one of our customer, this is the amplifier that pair with it. The back-lit effect of the old school window grill that casted on the surface is sweet. This is what the designer spoken to me: “From 3D model to Final Product is the...